Company Info | IBA Staff | PhotosINFO | Dealer Info | Contact Us | Terms | Customer Comments | HOME
Iron Brigade Armory
Weapons Systems
Rifle Accurizing
Available Rifles
One of a Kind
One Piece Scope Mounts
Remington M700 Receivers

Rifle Finishes
Manowar Finish
Parkerizing
Weapon Painting

Weapons Parts
M700
AR-15
MISC

Books
IBA (DFA, WF, OSB)
Roy F. Chandler Titles
About Rocky's Books
Data Books/Mildot
Manuals
Owens

IBA Apparel
T-Shirts
Sweatshirts
Polo Shirts
MISC

Ammo
Brass
Scope Mounts
Night Vision
Rifle Stocks
Magazines
Nylon Gear
Rifle Slings/Hardware
Cases
Tools
Cleaning
Misc Accessories

>> NEW <<

Products by Manufacturer

Accurizing

*Please note* All weapons that enter our Armory are given a thorough LTI [Limited Technical Inspection].  Any problems, major and/or minor will brought to your attention before corrected [additional charges may apply and will need to be approved]. 

If you decide NOT to have these problems corrected, the minimum charge will be one shop hour = $75- for the LTI.

M700 REMINGTON ACCURACY TUNE UP (Basic)

  • Ship your personal or department rifle to IBA [please refer to our shipping protocol]
  • Basic Tune Up for all Remington M700’s with an aluminum bedding block [PSS, LTR or Varmint Synthetic rifles, etc.] Stocks with bedding blocks may include HS Precision or Bell & Carlson [BCS 1000] type stocks, etc.
  • Short Action 1" Mount prices shown - Add $20.00 for Long Action or 30MM rings
  • All rifles are given a thorough inspection (LTI) by our competent staff of Armorers.  Serious problems, like excessive headspace, will be brought to your attention before dollars are spent on the upgrade.
  • If the weapon is returned at this point [without proceeding with work], the minimum charge will be $75- for the LTI plus return shipping charges
  • Standard turnaround time is 3-4 weeks.

Work Performed:

  • Perform "LTI" Inspect Headspace, Bore Erosion and all Trigger Parts
  • Chase all threads on the Receiver
  • Recrown Muzzle with diameter of Bore for more consistent shots
  • Polish Feed Ramp, fit Magazine Box
  • Clear Aluminum Bedding Block to allow proper Receiver / Bedding contact
  • Epoxy Sling Swivel Studs to prevent loosening
  • Re-paint Barrel Channel to help eliminate Oils and Solvents from penetrating the Stock
  • Disassemble, Clean and re-lubricate all trigger parts
  • Set Trigger Pull to 3 3/4 lb's, Set Sear Engagement and Overtravel and re-seal screws
  • Install HK 3/16 torque bolts. Torque set rifles provide shot to shot consistency
  • Install IBA One Piece Target Mount (20MOA of Built in Elevation)
  • Install/Re-install customer scope and boresight
  • Test Fire and rezero for 100 yards
  • Completely Clean and lube all moving parts

Pricing TBD on a case by case basis – Contact nchandler@ironbrigadearmory.com 


M700 REMINGTON ACCURACY TUNE UP (Master)

Master Tune Up for Remington M700 PSS, LTR or Varmint Synthetic Rifles with HS Precision Stocks ONLY.  All McMillan stocked rifles are quoted individually after the weapon has arrived and been inspected. If you have any questions please email us.

  • Master Tune Up for Remington M700’s [PSS, LTR or Varmint Synthetic Rifles with HS Precision, Bell & Carlson Type Stocks ONLY]. 
  • All McMillan stocked rifles are quoted individually after the weapon has arrived and been inspected. If you have any questions please email us.
  • Short Action 1" Mount prices shown - Add $20.00 for Long Action or 30MM rings

 

Work Performed:

  • Perform "LTI" Inspect Headspace, Bore Erosion and all Trigger Parts
  • Chase all threads on the Receiver
  • Recrown Muzzle with diameter of Bore for more consistent shots
  • Polish Feed Ramp, fit Magazine Box
  • Clear Aluminum Bedding Block to allow proper Receiver / Bedding contact
  • Epoxy Sling Swivel Studs to prevent loosening
  • Re-paint Barrel Channel to help eliminate Oils and Solvents from penetrating the Stock
  • Disassemble, Clean and re-lubricate all trigger parts
  • Set Trigger Pull to 3 3/4 lb's, Set Sear Engagement and Overtravel and re-seal screws
  • Install HK 3/16 torque bolts. Torque set rifles provide shot to shot consistency
  • Install IBA One Piece Target Mount (20MOA of Built in Elevation)
  • Install/Re-install customer scope and boresight
  • Test Fire and rezero for 100 yards
  • Completely Clean and lube all moving parts 
  • Includes all features of the Basic Tune Up (Shown above) plus:
    • Installation of the IBA Tactical Steel Trigger Guard and titanium barrel pad forward of the recoil lug.
    • The Tactical trigger guard replaces the alloy sporter guard making the rifle more resistant to damage due to field combat/tactical conditions. It also assists in maintaining "Battle Sight Zero" [BZO] as it anchors the receiver firmly in the bedding.
    • The titanium barrel pad positions the barreled action in the stock for consistent removal and re-installation without shifting the BZO.
    • Note: Stock must be routed and bedding material (Titanium Devcon ) applied. The entire weapon is re- parkerized in dark gray for added durability.

Pricing TBD on a case by case basis – Contact nchandler@ironbrigadearmory.com


 

Copyright © Iron Brigade Armory
Email | PH 910.455.3834 | Fax 910.346.1134
Best Viewed at 1024 x 768 or higher